- Stress is force per area and has SI unit pascal.
- Strain is relative deformation and is dimensionless.
- Young's modulus measures axial stiffness of a material in the linear-elastic range.
- For a uniform wire, ΔL=FL/(AY) under small uniaxial elastic strain.
- Hooke's law applies within the proportional region, not to every load.
- Bulk modulus measures resistance to fractional volume change under pressure.
- Shear modulus measures resistance to shear deformation.
- Poisson's ratio relates transverse and longitudinal strains.
- A stress, strain graph distinguishes proportionality, elastic response, plasticity and fracture.
- Elastic energy in a Hookean wire is ½FΔL.
- Axial stiffness depends on material modulus and specimen geometry.
- Always convert areas and extensions to SI units before solving.
Use these notes alongside your current textbook. Check important formulas, worked answers and syllabus coverage with your teacher or official learning material.
Mechanical Properties of Solids , Class 11 Physics
Original supplementary study guide on elasticity, stress, strain, Young's modulus, bulk and shear moduli, elastic energy, stress, strain curves, and numerical problem solving. Formulas use readable Unicode and mathematical HTML markup rather than raw LaTeX.
Learning outcomes
Distinguish force, stress, strain, stiffness and strength; identify elastic and plastic response; calculate Young's, bulk and shear moduli; interpret a stress, strain curve; and calculate energy stored during small elastic deformation.
Use SI units, specify loading conditions and state the range in which linear elasticity is assumed.
Elasticity and plasticity
Elastic deformation is recoverable when load is removed within the material's elastic range. Plastic deformation leaves a permanent change. Real materials may exhibit time-dependent behaviour; an ideal Hookean model is an approximation.
Normal stress and its SI unit
For a uniform axial load on a cross-sectional area A, average normal stress σ=F/A. Tensile stress pulls; compressive stress pushes. Unit: pascal (Pa)=N/m². For nonuniform loading, local stress need not equal this average.
Longitudinal strain
Longitudinal strain ε=ΔL/L₀, where L₀ is original gauge length and ΔL is signed change in length. It is dimensionless. Positive strain indicates extension under the chosen convention; negative indicates shortening.
Young's modulus
For small uniaxial elastic deformation of a uniform specimen, Y=σ/ε=FL₀/(AΔL), using consistent tensile signs. The result is in Pa. For a wire with fixed material and area, extension increases with force and original length.
Hooke's law and its limits
Within the linear proportional range, stress is proportional to strain, σ=Yε. The proportional limit and elastic limit need not coincide. A real stress, strain graph can depart from linearity while some deformation remains recoverable.
Spring constant versus Young's modulus
For a uniform wire under axial load in its linear range, F=kΔL with effective axial stiffness k=YA/L₀. The spring constant k has units N/m, whereas Young's modulus Y has units Pa. A thicker wire is stiffer at the same length and material.
Lateral strain and Poisson's ratio
A tensile specimen usually narrows transversely. Poisson's ratio ν=−(lateral strain)/(longitudinal strain) in small-strain linear elasticity. It is dimensionless; the minus sign makes ν positive for common materials that contract laterally under tension.
Volume strain and bulk modulus
Volume strain is ΔV/V₀. Under a small increase in uniform external pressure ΔP, bulk modulus B=−ΔP/(ΔV/V₀), provided compression is small and the response is elastic. B is positive for ordinary stable materials; unit Pa.
Compressibility
Compressibility κ=1/B in the linear regime; unit Pa⁻¹. A large bulk modulus means small fractional volume change for a given pressure change.
Shear stress and shear strain
Tangential force per area is shear stress τ=F/A. For a small shear angle θ (in radians), shear strain γ≈θ≈x/h, where x is lateral displacement and h is specimen height. Shear modulus Gₛ=τ/γ, unit Pa.
Distinguish the three elastic moduli
Young's modulus measures axial resistance to stretching or compression; bulk modulus measures resistance to volume change under hydrostatic pressure; shear modulus measures resistance to change of shape under tangential stress. The symbols Y, B and Gₛ must not be confused with gravitational constant G.
Stress, strain graph: initial region
The initial straight-line portion of an ideal tensile stress, strain graph has slope Young's modulus. At the end of proportionality, the graph may curve. The elastic limit marks the largest stress from which the material recovers without permanent strain under the stated test conditions.
Yielding, plastic region and ultimate strength
After yielding, plastic deformation becomes significant. The ultimate tensile strength is the maximum engineering stress on a typical tensile test curve. Fracture occurs at failure; the ultimate strength and fracture stress are not necessarily equal.
Ductile and brittle materials
Ductile materials can undergo substantial plastic deformation before fracture; brittle materials typically fail with relatively little plastic strain. These descriptions depend on temperature, loading rate and test conditions.
Elastic potential energy in a stretched wire
If force rises linearly from zero to F during extension ΔL, stored elastic energy U=½FΔL=½k(ΔL)². Energy per original volume is u=½σε=σ²/(2Y)=½Yε² for uniform uniaxial small-strain linear elasticity.
Work from a force, extension graph
The work done in a quasistatic extension equals the area under the F, ΔL curve. A straight line through the origin gives triangular area ½FΔL. Nonlinear loading requires the actual area or an integral.
Elastic energy and loading, unloading losses
In an ideal perfectly elastic process, stored energy is recovered upon unloading. Real materials can dissipate energy through hysteresis and internal friction, so loading and unloading curves may differ.
Wire extension with changing dimensions
For identical material under the same axial force, ΔL=FL/(YA). Doubling length doubles extension; doubling area halves extension, provided the linear-elastic uniform-wire assumptions remain valid.
Series and parallel elastic wires
For two axial wires in series carrying the same force, extensions add and 1/kₑq=1/k₁+1/k₂. For ideal parallel wires with equal extension, forces add and kₑq=k₁+k₂. State how the wires are connected before applying these relations.
Stress versus pressure
Pressure is a scalar normal compressive load under hydrostatic conditions. Stress is generally a tensor with normal and shear components. In basic one-dimensional questions, average stress is often written F/A, but the physical loading mode matters.
Dimensional checks
Stress, Young's modulus, bulk modulus and shear modulus all have dimensions M L⁻¹ T⁻². Strain and Poisson's ratio are dimensionless. Spring stiffness has dimensions M T⁻².
Practical uses
Elastic design matters in bridges, cables, springs, pressure vessels and structures. Modulus describes stiffness, not necessarily strength: a material can be stiff yet brittle. Safe design also requires allowable stress, fatigue and appropriate safety factors.
Common errors and safeguards
Convert mm² to m² by multiplying by 10⁻⁶; convert mm extension to m by multiplying by 10⁻³. Use original length for engineering strain. Do not assume stress and strain are proportional after the proportional limit. Do not confuse Young's modulus with spring constant or strain with displacement.
Worked example 1: Axial stress
A wire carries 200 N over area 2 mm². A=2×10⁻⁶ m², so σ=200/(2×10⁻⁶)=1×10⁸ Pa.
Worked example 2: Longitudinal strain
A 2 m rod lengthens by 0.4 mm. ε=0.0004/2=2×10⁻⁴.
Worked example 3: Young's modulus
For stress 1×10⁸ Pa and strain 5×10⁻⁴, Y=(1×10⁸)/(5×10⁻⁴)=2×10¹¹ Pa.
Worked example 4: Wire extension
A wire has F=100 N, L=2 m, A=1×10⁻⁶ m² and Y=2×10¹¹ Pa. ΔL=FL/(AY)=200/(2×10⁵)=0.001 m=1 mm.
Worked example 5: Axial stiffness
A 1 m wire with A=2×10⁻⁶ m² and Y=1×10¹¹ Pa has k=YA/L=2×10⁵ N/m.
Worked example 6: Force from stiffness
An ideal wire of stiffness 4×10⁴ N/m extends by 0.5 mm. F=kΔL=4×10⁴×0.0005=20 N.
Worked example 7: Extension when length doubles
For the same F, A and Y, doubling L from 1 m to 2 m doubles ΔL, since ΔL∝L.
Worked example 8: Extension when radius doubles
A circular wire's area is proportional to radius squared. Doubling radius quadruples area, so extension becomes one-quarter for unchanged F, L and Y.
Worked example 9: Elastic energy
A wire stretches 2 mm under a final force of 50 N in the linear range. U=½FΔL=½×50×0.002=0.05 J.
Worked example 10: Elastic energy density
For σ=2×10⁷ Pa and ε=1×10⁻⁴, u=½σε=1000 J/m³.
Worked example 11: Bulk modulus
Pressure increases by 2×10⁶ Pa and volume decreases by 0.1%. ΔV/V=−0.001, so B=−(2×10⁶)/(−0.001)=2×10⁹ Pa.
Worked example 12: Volume change under pressure
A sample of initial volume 0.02 m³ has B=1×10⁹ Pa. A pressure increase of 5×10⁶ Pa gives ΔV=−VΔP/B=−0.0001 m³.
Worked example 13: Compressibility
For B=2×10⁹ Pa, κ=1/B=5×10⁻¹⁰ Pa⁻¹.
Worked example 14: Shear strain
A block 0.1 m high has its top shifted sideways by 0.2 mm. γ≈x/h=0.0002/0.1=0.002.
Worked example 15: Shear modulus
Shear stress 6×10⁶ Pa produces shear strain 0.003. Gₛ=τ/γ=2×10⁹ Pa.
Worked example 16: Shear force
A face of area 0.01 m² experiences shear stress 4×10⁴ Pa. Tangential force F=τA=400 N.
Worked example 17: Poisson's ratio
Longitudinal strain is +0.002 and lateral strain −0.0006. ν=−(−0.0006)/0.002=0.3.
Worked example 18: Lateral contraction
A rod of diameter 10 mm experiences tensile longitudinal strain 0.001 with ν=0.25. Lateral strain=−0.00025, so diameter change is −0.0025 mm.
Worked example 19: Series springs
Two ideal axial springs have k₁=100 N/m and k₂=300 N/m in series. kₑq=(100×300)/(100+300)=75 N/m.
Worked example 20: Parallel springs
Two ideal springs of 100 and 300 N/m act in parallel. kₑq=100+300=400 N/m.
Worked example 21: Force, extension area
Force rises linearly from 0 to 80 N over 4 mm. Work=½×80×0.004=0.16 J.
Worked example 22: Stress unit conversion
A tensile stress of 150 MPa equals 150×10⁶ Pa=1.5×10⁸ Pa.
Worked example 23: Modulus unit conversion
Young's modulus 200 GPa equals 200×10⁹ Pa=2×10¹¹ Pa.
Worked example 24: Find area from extension
A rod has F=50 N, L=1 m, Y=1×10¹¹ Pa and ΔL=0.5 mm. A=FL/(YΔL)=50/(1×10¹¹×0.0005)=1×10⁻⁶ m².
Worked example 25: Find force from extension
A 2 m wire with A=1×10⁻⁶ m², Y=2×10¹¹ Pa and ΔL=1 mm needs F=YAΔL/L=100 N.
Worked example 26: Find original length
For F=60 N, A=2×10⁻⁶ m², Y=1×10¹¹ Pa and ΔL=0.3 mm, L=YAΔL/F=1 m.
Worked example 27: Compare two wires
Equal force acts on two equal-length wires of same material. Wire A has twice the area of B. Since ΔL∝1/A, wire A extends half as much.
Worked example 28: Recoverable energy from a stress, strain curve
An ideal material reaches stress 4×10⁷ Pa at strain 0.002 along a straight line. Stored energy density is ½×4×10⁷×0.002=4×10⁴ J/m³.
Worked example 29: Force required for target stress
To produce stress 5×10⁷ Pa on area 4 mm², F=σA=5×10⁷×4×10⁻⁶=200 N.
Worked example 30: Maximum force at a stress limit
If permissible tensile stress is 8×10⁷ Pa and area is 3 mm², Fₘₐₓ=σₘₐₓA=8×10⁷×3×10⁻⁶=240 N.
Worked example 31: Elastic strain at given modulus
A specimen has Y=1.5×10¹¹ Pa and σ=3×10⁷ Pa. ε=σ/Y=2×10⁻⁴.
Worked example 32: Energy for an axial rod
A rod has axial stiffness k=2×10⁵ N/m and stretches 1 mm. U=½k(ΔL)²=½×2×10⁵×10⁻⁶=0.1 J.
Worked example 33: Bulk volume reduction percentage
With ΔP=1×10⁷ Pa and B=5×10⁹ Pa, ΔV/V=−0.002, a 0.2% volume reduction.
Worked example 34: Stress from strain and Young's modulus
For Y=2×10¹¹ Pa and ε=1.5×10⁻⁴, σ=Yε=3×10⁷ Pa.
Worked example 35: Extension of a thin wire
For F=20 N, L=1.5 m, A=0.5 mm² and Y=1.2×10¹¹ Pa, ΔL=30/(0.5×10⁻⁶×1.2×10¹¹)=0.0005 m=0.5 mm.
Worked example 36: Extension under compression
A 0.5 m column with area 0.01 m² and Y=2×10¹⁰ Pa is compressed by 1×10⁵ N. Magnitude of shortening=FL/(AY)=5×10⁴/(2×10⁸)=2.5×10⁻⁴ m=0.25 mm.
Worked example 37: Spring energy quadrupling
If a Hookean spring's extension doubles, stored energy U=½kx² becomes four times as large.
Worked example 38: Young's modulus from graph slope
A straight stress, strain segment rises by 6×10⁷ Pa as strain rises by 3×10⁻⁴. Slope Y=2×10¹¹ Pa.
Worked example 39: Axial series extension
Two wires in series have stiffness 200 and 300 N/m, carrying 12 N. Total extension=12/200+12/300=0.10 m.
Worked example 40: Axial parallel force split
Two ideal wires in parallel with k₁=100 N/m and k₂=300 N/m extend together by 0.02 m. Forces are 2 N and 6 N; total 8 N.
Practice MCQs , options, answers and explanations
Question 1. SI unit of stress?
- N
- Pa
- J
Correct answer: B. Pa
Explanation: Stress is force divided by area.
Question 2. Longitudinal strain is:
- Dimensionless
- Measured in newtons
- Measured in metres
Correct answer: A. Dimensionless
Explanation: It is a ratio of two lengths.
Question 3. Young's modulus is:
- Stress/strain
- Force/extension
- Strain/stress
Correct answer: A. Stress/strain
Explanation: Y is the slope of the initial linear stress, strain curve.
Question 4. A wire's length doubles at fixed F, A and Y. Extension:
- Halves
- Doubles
- Does not change
Correct answer: B. Doubles
Explanation: ΔL=FL/(AY).
Question 5. Wire radius doubles with other conditions fixed. Extension:
- Becomes one-quarter
- Doubles
- Quadruples
Correct answer: A. Becomes one-quarter
Explanation: Area increases fourfold.
Question 6. Bulk modulus concerns:
- Volume change under pressure
- Bending only
- Temperature only
Correct answer: A. Volume change under pressure
Explanation: It measures hydrostatic compressibility.
Question 7. The shear modulus has SI unit:
- Pa
- m
- N·s
Correct answer: A. Pa
Explanation: Shear stress divided by shear strain has pressure units.
Question 8. An ideal Hookean spring stores energy:
- kx
- ½kx²
- 2kx
Correct answer: B. ½kx²
Explanation: Work is area under the linear force, extension graph.
Question 9. What does the slope of an initial stress, strain straight line give?
- Young's modulus
- Density
- Mass
Correct answer: A. Young's modulus
Explanation: σ=Yε in the proportional region.
Question 10. For positive bulk modulus, increasing external pressure generally:
- Decreases volume
- Increases volume
- Has no effect
Correct answer: A. Decreases volume
Explanation: ΔV/V=−ΔP/B.
Question 11. Poisson's ratio is:
- Dimensionless
- Measured in Pa
- Measured in N/m
Correct answer: A. Dimensionless
Explanation: It is a ratio of strains.
Question 12. The elastic limit refers to:
- Maximum recoverable stress under stated conditions
- Breaking force always
- Ultimate tensile strength always
Correct answer: A. Maximum recoverable stress under stated conditions
Explanation: Beyond the elastic limit permanent deformation remains.
Short-answer practice , questions and answers
Question 1. Define average normal stress.
Answer: σ=F/A, force per cross-sectional area, measured in pascals.
Question 2. Define longitudinal strain.
Answer: ε=ΔL/L₀; it has no SI unit.
Question 3. Write Young's modulus for a uniform wire.
Answer: Y=FL₀/(AΔL) in the small-strain linear-elastic regime.
Question 4. What is Hooke's law?
Answer: Within the proportional region, stress is proportional to strain.
Question 5. What is bulk modulus?
Answer: B=−ΔP/(ΔV/V₀) for small hydrostatic elastic compression.
Question 6. What is shear modulus?
Answer: Gₛ=τ/γ, the ratio of shear stress to shear strain.
Question 7. Why is strain dimensionless?
Answer: It is a ratio of like quantities, such as change in length divided by original length.
Question 8. How is stiffness different from Young's modulus?
Answer: Axial stiffness k=YA/L depends on geometry; Y is a material property under stated conditions.
Question 9. What is the energy in a Hookean spring?
Answer: U=½kx², where x is extension or compression from equilibrium.
Question 10. What is the area under a force, extension graph?
Answer: Work done during the loading process; for ideal reversible loading, stored elastic energy.
Question 11. What is Poisson's ratio?
Answer: ν=−lateral strain/longitudinal strain in small-strain linear elasticity.
Question 12. What is the difference between ductile and brittle response?
Answer: Ductile materials generally show substantial plastic strain before fracture; brittle ones relatively little.
Long-answer practice , step-by-step solutions
Question 1. Derive extension of a uniform wire.
Step-by-step solution:
- For axial load F and area A, stress is σ=F/A.
- Longitudinal strain is ε=ΔL/L₀.
- Within the linear region Y=σ/ε=(F/A)/(ΔL/L₀).
- Rearrange to obtain ΔL=FL₀/(AY). Check metres, newtons and pascals.
Question 2. Derive elastic energy stored in a stretched wire.
Step-by-step solution:
- Within Hooke's law, F=kx where x is extension.
- Small incremental work is dW=Fdx=kx dx.
- Integrate from 0 to ΔL: U=∫₀^ΔL kx dx=½k(ΔL)².
- Since final F=kΔL, U=½FΔL. This assumes quasistatic reversible linear loading.
Question 3. Explain a tensile stress, strain curve.
Step-by-step solution:
- Initially stress increases proportionally with strain, and the slope is Young's modulus.
- Beyond the proportional limit, the curve may become nonlinear while deformation can remain elastic.
- Beyond the elastic limit, unloading leaves permanent strain; yield behaviour may occur.
- Ultimate tensile strength is the peak engineering stress; fracture follows at failure.
Question 4. Solve a wire-extension and energy problem.
Step-by-step solution:
- Given F=100 N, L=2 m, A=1×10⁻⁶ m², Y=2×10¹¹ Pa.
- Compute ΔL=FL/(AY)=200/(2×10⁵)=0.001 m.
- Strain ε=0.001/2=5×10⁻⁴ and stress σ=100/(10⁻⁶)=1×10⁸ Pa.
- Stored energy U=½FΔL=0.05 J.
Question 5. Derive the bulk-modulus relation and interpret its sign.
Step-by-step solution:
- Define fractional volume strain as ΔV/V₀.
- For small uniform hydrostatic pressure increase ΔP, ordinary materials contract, so ΔV is negative.
- Define B=−ΔP/(ΔV/V₀), making B positive for stable compressive response.
- Rearrange to ΔV=−V₀ΔP/B; note the linear approximation and small-strain assumptions.
Question 6. Explain two wires in series and parallel.
Step-by-step solution:
- For each ideal axial wire, k=YA/L.
- In series, both wires carry the same force and extensions add: ΔL=F/k₁+F/k₂, giving 1/kₑq=1/k₁+1/k₂.
- In parallel, wires have the same extension and forces add: F=(k₁+k₂)ΔL, giving kₑq=k₁+k₂.
- State that joints, loading and geometry are idealised.
Formula revision sheet
Stress: σ=F/A; longitudinal strain: ε=ΔL/L₀; Young's modulus: Y=FL₀/(AΔL); axial stiffness: k=YA/L₀.
Bulk modulus: B=−ΔP/(ΔV/V₀); compressibility: κ=1/B; shear modulus: Gₛ=τ/γ; Poisson's ratio: ν=−εₗₐₜ/εₗₒₙg.
Elastic energy: U=½FΔL=½k(ΔL)²; elastic energy density: u=½σε. Stress and all elastic moduli use Pa; strains are dimensionless.
Revision checklist
Define stress and strain with correct units; distinguish proportional and elastic limits; derive ΔL=FL/(AY); read stress, strain graphs; calculate bulk and shear moduli; use force, extension area for stored energy.
In numericals: write given quantities, convert units, choose a model, substitute with units, check answer size, and state physical assumptions.
Source and curriculum scope
This is original supplementary learning material, not a reproduction of NCERT text or a claim to solve every numbered textbook exercise. Confirm prescribed 2026, 27 topics with the official CBSE curriculum and NCERT textbook.
Frequently asked questions
What is stress?
Average normal stress is force divided by cross-sectional area, σ=F/A, measured in pascals.
What is strain?
Longitudinal strain is change in length divided by original length, ε=ΔL/L₀, and is dimensionless.
What is Young's modulus?
In the small-strain linear-elastic regime, Y=stress/strain=FL₀/(AΔL). Its unit is Pa.
What is Hooke's law?
Within the proportional region, stress is directly proportional to strain.
What is bulk modulus?
Bulk modulus B=−ΔP/(ΔV/V₀) measures resistance to fractional volume reduction under a small pressure increase.
What is shear modulus?
Shear modulus is shear stress divided by shear strain, Gₛ=τ/γ, in the linear-elastic regime.
How is elastic energy calculated?
For ideal linear loading, U=½FΔL=½k(ΔL)².
Are all numbered NCERT exercises covered?
No. This is an original supplementary guide with worked examples and practice, not a verified exercise-by-exercise reproduction.
