- Pressure is normal force per area, measured in pascals.
- Hydrostatic pressure difference in a constant-density fluid is ρgh.
- Absolute and gauge pressure differ by atmospheric pressure.
- Pascal's principle enables hydraulic force multiplication without creating energy.
- Buoyancy equals the weight of displaced fluid.
- Floating equilibrium balances buoyancy and weight.
- Steady incompressible continuity gives A₁v₁=A₂v₂.
- Bernoulli's equation needs ideal steady flow assumptions.
- Viscosity resists shear; Stokes drag applies in the creeping-flow regime.
- Terminal speed occurs when forces balance.
- Surface tension is measured in N/m; a soap film has two interfaces.
- Capillary rise depends on surface tension, contact angle, density and tube radius.
Use these notes alongside your current textbook. Check important formulas, worked answers and syllabus coverage with your teacher or official learning material.
Mechanical Properties of Fluids , Class 11 Physics
Original study guide with fluid statics, dynamics, viscosity and surface effects. All practice questions are individually structured, and mathematical notation uses readable symbols without raw LaTeX.
Learning objectives
Explain fluid pressure and buoyancy; calculate hydraulic force; use continuity and Bernoulli equations with stated assumptions; distinguish laminar from turbulent flow; solve viscosity, terminal speed, surface tension and capillarity problems.
Keep pressure units in pascals, density in kg/m³, and lengths in metres.
Fluids and density
Liquids and gases flow and cannot sustain a static shear stress in equilibrium. Mass density ρ=m/V, with SI unit kg/m³. The fluid density may vary with temperature and pressure; many introductory liquid problems assume constant ρ.
Pressure and normal force
Pressure is normal force per unit area: p=F⊥/A for uniform loading. Its SI unit is pascal (Pa)=N/m². Pressure is a scalar in a fluid at rest, and the force on a small surface acts perpendicular to that surface.
Absolute pressure versus gauge pressure
Absolute pressure is measured relative to vacuum; gauge pressure is measured relative to surrounding atmospheric pressure. pₐᵦₛ=pₐₜₘ+p₍gauge₎. A gauge reading of zero can still correspond to substantial absolute pressure.
Hydrostatic pressure derivation
For a stationary fluid of constant density, vertical force balance on a column of height h gives Δp=ρgh. At depth h below a free surface at pressure p₀, p=p₀+ρgh. Depth is measured vertically, not along a sloping wall.
Hydrostatic pressure at equal depth
In the same connected stationary fluid, pressure at points at the same horizontal level is equal, provided relevant interfaces and density variations are accounted for. Vessel shape does not change p=p₀+ρgh at a fixed depth.
Pascal's principle
A pressure change applied to a confined incompressible fluid is transmitted throughout it under static conditions. Ideal hydraulic devices use F₁/A₁=F₂/A₂; the output force can be larger, but output displacement is correspondingly smaller.
Hydraulic machine and energy conservation
For an ideal hydraulic press, volume conservation gives A₁d₁=A₂d₂. Thus F₁d₁=F₂d₂, ignoring friction and fluid losses. Force multiplication does not create energy.
Atmospheric pressure and manometers
A mercury barometer balances atmospheric pressure against a mercury column: pₐₜₘ=ρHg gh in the simplified model. A U-tube manometer uses pressure differences balanced by fluid-column heights. Carefully identify the fluids and free surfaces.
Archimedes' principle
The upward buoyant force equals the weight of displaced fluid: Fᵦ=ρfluid g Vdisplaced, for a static fluid under uniform gravity. The submerged or displaced volume is used, not automatically the object's entire volume.
Floating and sinking
A freely floating object in static equilibrium has buoyant force equal to its weight. For a uniform object floating in one fluid, submerged fraction Vsub/Vtotal=ρobject/ρfluid when ρobject is less than ρfluid. A sinking object can still experience buoyancy.
Apparent weight in a fluid
For a fully immersed stationary object supported by a scale, apparent weight is mg−Fᵦ when the only other vertical forces are weight, buoyancy and support. Avoid using this expression blindly if additional forces or acceleration are present.
Steady and streamline flow
Steady flow has time-independent velocity at each fixed point. Streamlines are tangent to local velocity. Flow can be steady without being uniform in space. In laminar flow, layers move smoothly; turbulence contains irregular fluctuations.
Continuity equation
Conservation of mass gives ρ₁A₁v₁=ρ₂A₂v₂ for steady one-dimensional flow through a streamtube. For incompressible flow, A₁v₁=A₂v₂. Use cross-sectional mean speed when the velocity profile is not uniform.
Bernoulli's equation
Along a streamline for steady, incompressible, nonviscous flow with no pumps or dissipative losses, p+½ρv²+ρgh is constant. Pressure, kinetic and gravitational terms all have units of Pa. It cannot be applied indiscriminately across viscous pipes or unrelated streamlines.
Torricelli's law
For a large tank draining through a small opening to the atmosphere, ideal outflow speed is v≈√(2gh), where h is the vertical difference between the free surface and the opening. This assumes negligible free-surface speed and losses.
Venturi effect
In an ideal horizontal pipe, a narrower section has higher mean speed by continuity and lower static pressure by Bernoulli. Real pressure recovery is reduced by viscous losses.
Viscosity and Newton's law of viscosity
For a Newtonian fluid under simple shear, shear stress τ=η(dv/dy), where η is dynamic viscosity, with SI unit Pa·s. The sign and direction depend on the chosen axes; viscosity resists relative shearing motion.
Stokes' drag
For a small sphere moving slowly through a viscous fluid in the creeping-flow regime, drag magnitude is Fd=6πηrv. This formula assumes an appropriate low Reynolds number and idealised flow conditions.
Terminal speed of a small sphere
At terminal speed in a viscous fluid, weight minus buoyancy equals drag. Under Stokes-flow conditions, vt=2r²(ρsphere−ρfluid)g/(9η), for a denser sphere settling downward. Do not use this at high Reynolds numbers.
Reynolds number
Re=ρvD/η is dimensionless and compares inertial and viscous effects. In pipe flow it helps indicate flow regime; transition thresholds depend on geometry, disturbances and conditions.
Surface tension
Surface tension T is force per unit length along a liquid surface, SI unit N/m, and equivalently surface energy per unit area under appropriate conditions. For a soap film with two surfaces, a sliding-wire force is 2Tℓ, not Tℓ.
Excess pressure in drops and bubbles
For a spherical liquid drop with one interface, excess pressure Δp=2T/r. For a thin soap bubble with two interfaces, Δp=4T/r, assuming equal surface tension and negligible film thickness.
Contact angle and wetting
The contact angle θ is measured through the liquid at the solid surface. A contact angle below 90° favours capillary rise in a narrow tube; above 90° can produce depression. Surface contamination changes wetting behaviour.
Capillary rise and depression
For a circular capillary of radius r, h=2Tcosθ/(ρgr) relative to the surrounding free surface, under static conditions and neglecting corrections. A negative cosθ gives a depression (negative h).
Dimensional and unit checks
Pressure and energy density have unit Pa=N/m²; dynamic viscosity has Pa·s; surface tension has N/m; kinematic viscosity has m²/s; volume flow rate Q=Av has m³/s.
Common mistakes
Do not confuse depth with height above ground, gauge with absolute pressure, displaced with total volume, or pressure with force. For Bernoulli, verify steady inviscid assumptions and compare points on the same streamline. Convert cm² and mm into SI before substitution.
Worked example 1: Pressure on a piston
A 300 N normal force acts on area 0.02 m². p=300/0.02=15,000 Pa.
Worked example 2: Gauge pressure at depth
At 2 m in water with ρ=1000 kg/m³ and g=10 m/s², pg=ρgh=20,000 Pa.
Worked example 3: Absolute pressure underwater
At 3 m depth with pₐₜₘ=100,000 Pa, ρ=1000 kg/m³ and g=10, pabs=100,000+30,000=130,000 Pa.
Worked example 4: Pressure difference between depths
At depths 2 m and 7 m in the same stationary water, Δp=1000×10×(7−2)=50,000 Pa.
Worked example 5: Hydraulic force multiplication
Small piston area 2 cm², large piston area 100 cm², input force 40 N. F₂=40×100/2=2000 N.
Worked example 6: Hydraulic piston displacement
For the same press with area ratio 1:50, if small piston travels 0.5 m, large piston moves 0.5/50=0.01 m.
Worked example 7: Density from mass and volume
A fluid has mass 1.5 kg in 0.002 m³. ρ=1.5/0.002=750 kg/m³.
Worked example 8: Buoyant force for submerged block
A block displaces 0.003 m³ of water. Fᵦ=1000×10×0.003=30 N.
Worked example 9: Apparent weight
A 5 kg fully immersed object displaces 0.002 m³ of water; g=10. Weight=50 N, buoyancy=20 N, apparent weight=30 N.
Worked example 10: Floating fraction
A wood block of density 600 kg/m³ floats in water of density 1000 kg/m³. Submerged fraction=600/1000=0.6 or 60%.
Worked example 11: Displaced volume of floating mass
A 2 kg object floats in water at g=10. Set ρgV=mg, so V=2/1000=0.002 m³.
Worked example 12: Continuity with area change
Pipe area decreases from 8 cm² to 2 cm². If inlet mean speed is 1 m/s, outlet speed=8×1/2=4 m/s.
Worked example 13: Volume flow rate
Water flows at 2 m/s through area 0.005 m². Q=Av=0.01 m³/s.
Worked example 14: Flow time for tank volume
A 0.3 m³ container fills at constant Q=0.01 m³/s. Time=0.3/0.01=30 s.
Worked example 15: Bernoulli pressure drop
Horizontal ideal water pipe has speeds 2 and 6 m/s. p₁−p₂=½ρ(v₂²−v₁²)=500×32=16,000 Pa.
Worked example 16: Torricelli outflow
For h=5 m and g=10 m/s², ideal outflow speed √(2×10×5)=10 m/s.
Worked example 17: Pressure head
A gauge pressure of 30,000 Pa in water corresponds to head h=p/(ρg)=3 m for ρ=1000 and g=10.
Worked example 18: Viscous shear stress
For η=0.5 Pa·s and velocity gradient 4 s⁻¹, shear stress magnitude τ=η×4=2 Pa.
Worked example 19: Viscous force
A plate area 0.2 m² experiences shear stress 3 Pa. Force magnitude=τA=0.6 N.
Worked example 20: Viscosity from force
A 0.1 m² plate moving at 0.2 m/s over a stationary plate separated by 1 mm needs force 4 N. η=Fh/(Av)=4×0.001/(0.1×0.2)=0.2 Pa·s.
Worked example 21: Stokes drag
For η=0.1 Pa·s, r=0.001 m and v=0.02 m/s, Fd=6π×0.1×0.001×0.02≈3.77×10⁻⁵ N.
Worked example 22: Terminal speed scaling
In the Stokes regime for the same materials and fluid, doubling sphere radius makes terminal speed four times as large, since vt∝r².
Worked example 23: Reynolds number
For ρ=1000 kg/m³, v=0.1 m/s, D=0.01 m and η=0.001 Pa·s, Re=1000×0.1×0.01/0.001=1000.
Worked example 24: Surface-tension force on wire
A soap film with T=0.03 N/m and movable wire length 0.1 m pulls with F=2Tℓ=0.006 N.
Worked example 25: Liquid drop excess pressure
For a drop radius 0.001 m and T=0.07 N/m, Δp=2T/r=140 Pa.
Worked example 26: Soap bubble excess pressure
For soap bubble radius 0.002 m and T=0.03 N/m, Δp=4T/r=60 Pa.
Worked example 27: Capillary rise
For T=0.072 N/m, θ=0°, ρ=1000, g=10, r=0.0005 m, h=2×0.072/(1000×10×0.0005)=0.0288 m=2.88 cm.
Worked example 28: Capillary radius scaling
For the same liquid and contact angle, halving tube radius doubles capillary rise magnitude.
Worked example 29: Contact angle effect
If θ=60° instead of 0° with all else fixed, cosθ changes from 1 to 0.5, so capillary rise halves.
Worked example 30: Pressure at different densities
At the same depth 4 m, fluid A with ρ=800 kg/m³ has gauge pressure 32,000 Pa, while water with ρ=1000 gives 40,000 Pa, taking g=10.
Worked example 31: Pascal press pressure
An input force 120 N on piston area 0.004 m² creates an ideal pressure increase of 30,000 Pa.
Worked example 32: Bernoulli speed from pressure
In a horizontal ideal water pipe, p₁−p₂=4500 Pa and v₁=1 m/s. v₂²=v₁²+2Δp/ρ=1+9=10, so v₂≈3.16 m/s.
Worked example 33: Efflux speed scaling
Ideal outflow speed is proportional to √h. Quadrupling head from 1 m to 4 m doubles the outflow speed.
Worked example 34: Submerged volume from buoyancy
A measured buoyant force of 15 N in water with g=10 gives V=15/(1000×10)=0.0015 m³.
Worked example 35: Floating equilibrium with weight
A floating object weighs 12 N. Its buoyant force is 12 N in equilibrium, independent of its shape.
Worked example 36: Liquid column pressure
A 0.75 m column of fluid density 1200 kg/m³ produces Δp=1200×10×0.75=9000 Pa.
Worked example 37: Mass flow rate
Water flows at Q=0.004 m³/s and density 1000 kg/m³. Mass flow rate ρQ=4 kg/s.
Worked example 38: Flow through a narrowing pipe
If diameter halves, area becomes one-quarter and mean speed becomes four times as large for steady incompressible flow.
Worked example 39: Capillary depression sign
For θ=120°, cosθ=−0.5, so h=2Tcosθ/(ρgr) is negative: the liquid level is depressed.
Worked example 40: Energy per volume in Bernoulli
For water density 1000 kg/m³ and speed 4 m/s, kinetic term ½ρv²=8000 Pa.
Practice MCQs , each option and answer separated
Question 1. SI unit of pressure?
- Pa
- N
- kg
Correct answer: A. Pa
Explanation: Pressure is normal force per area.
Question 2. Gauge pressure at depth h in constant-density fluid?
- ρgh
- ρg/h
- gh/ρ
Correct answer: A. ρgh
Explanation: Hydrostatic pressure difference is ρgh.
Question 3. Buoyant force equals:
- Weight of displaced fluid
- Always object weight
- Fluid pressure at top
Correct answer: A. Weight of displaced fluid
Explanation: Archimedes' principle applies to displaced fluid.
Question 4. For steady incompressible flow:
- Av is constant along a streamtube
- A/v is constant
- v always constant
Correct answer: A. Av is constant along a streamtube
Explanation: Continuity conserves volume flow rate.
Question 5. Bernoulli's equation assumes:
- Ideal steady flow along a streamline
- Any turbulent viscous flow
- Only stationary fluid
Correct answer: A. Ideal steady flow along a streamline
Explanation: Steady, inviscid, incompressible assumptions are essential.
Question 6. In a horizontal ideal pipe, a higher speed usually means:
- Lower static pressure
- Higher static pressure
- Unchanged pressure always
Correct answer: A. Lower static pressure
Explanation: Bernoulli balances pressure and kinetic terms.
Question 7. SI unit of dynamic viscosity?
- Pa·s
- N/m
- m/s
Correct answer: A. Pa·s
Explanation: η relates shear stress to velocity gradient.
Question 8. Surface tension SI unit?
- N/m
- N/m²
- Pa·s
Correct answer: A. N/m
Explanation: Surface tension is force per length.
Question 9. Excess pressure in a liquid drop?
- 2T/r
- 4T/r
- T/r²
Correct answer: A. 2T/r
Explanation: A drop has one liquid interface.
Question 10. Excess pressure in thin soap bubble?
- 4T/r
- 2T/r
- T/r
Correct answer: A. 4T/r
Explanation: A soap film has two interfaces.
Question 11. Capillary rise varies with tube radius as:
- 1/r
- r
- r²
Correct answer: A. 1/r
Explanation: h=2Tcosθ/(ρgr).
Question 12. At terminal velocity, net force is:
- Zero
- Always upward
- Always downward
Correct answer: A. Zero
Explanation: Drag, weight and buoyancy balance.
Short-answer practice , questions and answers
Question 1. Define pressure.
Answer: Pressure is normal force per unit area: p=F⊥/A.
Question 2. What is gauge pressure?
Answer: Pressure relative to the surrounding atmospheric pressure.
Question 3. State Pascal's principle.
Answer: An applied pressure change is transmitted throughout a confined static fluid under ideal conditions.
Question 4. State Archimedes' principle.
Answer: Buoyant force equals the weight of displaced fluid.
Question 5. What is the continuity equation?
Answer: ρAv is constant for steady one-dimensional flow; Av is constant for incompressible flow.
Question 6. Write Bernoulli's equation.
Answer: p+½ρv²+ρgh=constant along a streamline for ideal steady incompressible flow.
Question 7. What is viscosity?
Answer: Resistance of a fluid to relative shearing motion.
Question 8. What is terminal velocity?
Answer: The steady speed when the net force on a moving object becomes zero.
Question 9. Define surface tension.
Answer: Force per unit length along a liquid interface, in N/m.
Question 10. What is capillarity?
Answer: Rise or depression of liquid in a narrow tube caused by surface tension and wetting.
Question 11. Why does a floating object displace fluid?
Answer: Buoyancy from the displaced fluid balances its weight at equilibrium.
Question 12. Why can Bernoulli fail in a real pipe?
Answer: Viscous dissipation, turbulence, pumps and nonsteady effects can invalidate the ideal relation.
Long-answer practice , worked solutions
Question 1. Derive hydrostatic pressure.
Step-by-step solution:
- Consider a vertical stationary fluid column of area A and height h, density ρ.
- Its weight is ρAhg.
- Pressure force difference between bottom and top balances this weight: (pbottom−ptop)A=ρAhg.
- Thus pbottom−ptop=ρgh; if top pressure is p₀, p=p₀+ρgh.
Question 2. Derive hydraulic force and displacement relations.
Step-by-step solution:
- Pressure increment transmitted in an ideal hydraulic device satisfies F₁/A₁=F₂/A₂.
- Therefore F₂=F₁(A₂/A₁).
- For incompressible fluid, A₁d₁=A₂d₂, hence d₂=d₁(A₁/A₂).
- Multiplying gives F₁d₁=F₂d₂; no energy is created.
Question 3. Derive floating fraction.
Step-by-step solution:
- For a uniform object of density ρo and total volume V, weight is ρoVg.
- Displaced fluid of density ρf and submerged volume Vs exerts buoyancy ρfVs g.
- At floating equilibrium, ρoVg=ρfVs g.
- Therefore Vs/V=ρo/ρf, valid for a floating body in a single uniform fluid.
Question 4. Solve continuity and Bernoulli together.
Step-by-step solution:
- A horizontal ideal water pipe narrows from 4 cm² to 2 cm²; inlet speed is 2 m/s.
- Continuity gives outlet speed v₂=(4/2)×2=4 m/s.
- Bernoulli gives p₁−p₂=½ρ(v₂²−v₁²).
- With ρ=1000, pressure drop is 500(16−4)=6000 Pa.
Question 5. Derive Stokes terminal speed.
Step-by-step solution:
- For a sphere of radius r, weight is (4/3)πr³ρs g and buoyancy is (4/3)πr³ρf g.
- At terminal speed, downward effective weight balances upward Stokes drag 6πηrv.
- Thus (4/3)πr³(ρs−ρf)g=6πηrv.
- Solve vt=2r²(ρs−ρf)g/(9η), valid for creeping flow.
Question 6. Derive capillary rise.
Step-by-step solution:
- For tube radius r and contact angle θ, upward vertical component of surface-tension force is 2πrTcosθ.
- Weight of the supported liquid column relative to surrounding level is approximately πr²hρg.
- Equating gives 2πrTcosθ=πr²hρg.
- Thus h=2Tcosθ/(ρgr); negative h indicates depression.
Formula revision sheet
Pressure: p=F⊥/A; hydrostatics: Δp=ρgh; hydraulic press: F₁/A₁=F₂/A₂; buoyancy: Fᵦ=ρfluid g Vdisplaced.
Mass continuity: ρAv=constant; incompressible continuity: Av=constant; ideal Bernoulli: p+½ρv²+ρgh=constant; Torricelli: v=√(2gh).
Viscous shear: τ=η(dv/dy); Stokes drag: Fd=6πηrv; terminal speed: vt=2r²(ρsphere−ρfluid)g/(9η); Reynolds number: Re=ρvD/η.
Surface tension: T=F/ℓ for a single interface; liquid drop excess pressure: 2T/r; soap bubble: 4T/r; capillary height: h=2Tcosθ/(ρgr).
Exam revision and model assumptions
Always sketch the fluid geometry, choose pressure reference, identify whether fluid is stationary or flowing, and convert all measurements to SI units.
Check Bernoulli assumptions, displaced volume, number of film surfaces, Reynolds regime and capillary contact angle. Avoid applying Stokes' law outside low-Reynolds-number conditions.
Source and curriculum scope
Original supplementary material. It is not a reproduction of the NCERT textbook or a verified solution set for every numbered NCERT exercise. Exact 2026, 27 assessed scope and live mobile rendering require independent verification.
Frequently asked questions
What is fluid pressure?
Pressure is normal force per unit area, p=F/A, in pascals.
How does pressure vary with depth?
In a static constant-density fluid, pressure rises by ρgh over a depth h.
What is Archimedes' principle?
The upward buoyant force equals the weight of fluid displaced by the object.
What is the continuity equation?
For steady incompressible flow, the volume flow rate Av is constant along a streamtube.
When can Bernoulli's equation be used?
For ideal steady incompressible nonviscous flow along a streamline, without energy additions or losses.
What is viscosity?
Viscosity measures a fluid's resistance to relative shear; dynamic viscosity has SI unit Pa·s.
What causes capillary rise?
Surface tension and wetting forces can lift liquid in a narrow tube; h=2Tcosθ/(ρgr) under ideal static assumptions.
Does this solve every NCERT exercise?
No. It is an original supplementary guide; exact numbered exercise alignment has not been independently verified.
